Watlow Series SD31 PID with Optional Countdown Timer Instrukcja Użytkownika Strona 9
- Strona / 72
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
ç
Warning:
Use National Electric (NEC) or
other country-specific standard
wiring and safety practices when
wiring and connecting this con-
troller to a power source and to
electrical sensors or peripheral
devices. Failure to do so may re-
sult in damage to equipment and
property, and/or injury or loss of
life.
Spring clamp wiring connector
note:
To insert the wire, push the wire
into the desired connection num-
ber, and it should automatically
lock into place. To remove the
wire, press and hold the orange
release tab with a small screw-
driver. Pull the wire out of the
connection. Solid or tinned wire
recommended.
Note: To prevent ground loops,
isolation needs to be maintained
from input to output when using
switched DC or analog process
outputs.
ç
WARNING: Process input may
not have sensor break protec-
tion. Outputs can remain full on.
Watlow Series SD31 ■ 7 ■ Chapter 2 Install and Wire
Figure 7a — Thermocouple Input
(all model numbers)
Thermocouples are polarity sensitive. The negative lead (usually red) must be
connected to terminal 11.
• Input impedance: >20 MΩ
Figure 7b — RTD Input (100
ΩΩ
DIN curve 0.00385
ΩΩ
/
ΩΩ
/°C)
(all model numbers)
Terminals 8 and 11 must be shorted for a two-wire RTD. For three-wire RTDs,
the S1 lead (usually white) must be connected to terminal 10.
• Nominal excitation current: 390 µA
Figure 7c — 0 to 10V
ÎÎ
(dc) Process Input
(all model numbers)
• Input impedance 20 kΩ, dc only
Figure 7d — 0 to 50mV
ÎÎ
(dc) Process Input
(all model numbers)
• Input impedance >20 MΩ, dc only
3
4
8
9 10
11
5
6
7
9
11
6
8 9
10 11
9
11
+
-
3-wire RTD
6
8 9
10 11
S1 10
S3 11
S2 8
4
8
9 10
11
5
6
7
10
11
8
2-wire RTD
6
8 9
10 11
S1 10
11
S2 8
4
8
9 10
11
5
6
7
10
11
6
8 9
10 11
+10
-11
4
8
9 10
11
5
6
7
10
11
6
8 9
10 11
10
11
+
-
- User’s Manual 1
- Series SD31 1
- Single Display PID Controller 1
- Safety Information 2
- Technical Assistance 2
- Warranty 2
- Table of Contents 3
- Overview 4
- autotune 5
- Install and Wire 6
- Removing the SD31 Controller 7
- Wiring the Series SD31 8
- Figure 7b — RTD Input (100 9
- Figure 7c — 0 to 10V 9
- Figure 7d — 0 to 50mV 9
- 0 to 20 mA Process Input 10
- Output 1 Mechanical Relay 10
- Output 1 Solid-state Relay 10
- Output 1 Switched DC 11
- Output 1 Process 11
- Output 2 Mechanical Relay 11
- Output 2 Solid-state Relay 12
- Output 2 Switched DC 12
- Output 2 EIA/TIA-485 12
- 12VÎ (dc) 13
- Ethernet Gateway 14
- Home Page Overview 17
- ;ht] Rate Heat 18
- Setup Page Overview 19
- Factory Page Overview 20
- Programming Page Overview 20
- Read/Write 21
- Offset the input reading 31
- Programming Page Example 37
- Countdown Timer 38
- • SP is used when not timing 40
- Timer Example 44
- Calibrating the Series SD31 48
- Process Output Procedures 49
- Restoring Factory Calibration 49
- Features 50
- Operations Page 51
- Autotuning 51
- IS1 IS2 IS3 IS4 52
- 123 456 789 258 52
- Filter Time Constant 53
- Sensor Selection 53
- Access Lockout 53
- High Scale and Low Scale 53
- Control Methods 54
- On-Off Control 55
- Proportional Control 55
- (PID) Control 56
- Dead Band 56
- Nonlinear output curve 57
- Independent Heat and Cool PID 57
- Variable Time Base 57
- Process or Deviation Alarms 58
- Alarm Set Points 58
- Alarm Hysteresis 59
- Alarm Latching 59
- Alarm Silencing 59
- Retransmit 59
- Communications 60
- Troubleshooting 62
- Error Messages 64
- Appendix 65
- Power Supply H or L 67
- Output 1 C, K, F or J 67
- Output 2 A, C, K, J or U 67
- Timer Option A or T 67
- Prompt Index 70
- Series SD 71
- How to Reach Us 72
Powiązane produkty i podręczniki dla Czujniki Watlow Series SD31 PID with Optional Countdown Timer
Czujniki Watlow Series PD Instrukcja Użytkownika
(188 strony)
(188 strony)
Czujniki Watlow Series SD6 PID Controller with DeviceNet Addendum Instrukcja Użytkownika
(32 strony)
(32 strony)
Czujniki Watlow Series V4 Instrukcja Użytkownika
(21 strony)
(21 strony)
Czujniki Watlow Series SD PID-Regler und PID-Temperaturprofilfunkt Instrukcja Użytkownika
(80 strony)
(80 strony)
Czujniki Watlow TLM-8 Instrukcja Użytkownika
(8 strony)
(8 strony)
Czujniki Watlow WATVIEW Instrukcja Użytkownika
(36 strony)
(36 strony)
Czujniki Watlow Serie 96 Instrukcja Użytkownika
(92 strony)
(92 strony)
Czujniki Watlow Silver Series Instrukcja Użytkownika
(204 strony)
(204 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji