
Watlow EZ-ZONE
®
RML Module • 56 • Chapter 4 Setup Page
RM Limit Module • Setup Page
Display
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Probus
Index
Parameter
ID
Data
Type
&
Read/
Write
[SFn;B]
[SFn.b]
Timer (1 to 16)
Source Function B
Set the type of function
that will be used to reset
a retentive timer (reset
signal).
[nonE] None (61)
[ALM] Alarm Reset (6)
[`CPE] Compare (230)
[`Ctr] Counter (231)
[`dio] Digital I/O (1142)
[Ent;A] Profile Event Out A
(233)
[Ent;b] Profile Event Out B
(234)
[Ent;C] Profile Event Out C
(235)
[Ent;d] Profile Event Out D
(236)
[Ent;E] Profile Event Out E
(247)
[Ent;F] Profile Event Out F
(248)
[Ent;g] Profile Event Out G
(249)
[Ent;h] Profile Event Out H
(250)
[`FUn] Function Key (1001)
[`lgC] Logic (239)
[SoF;1] Special Function Out-
put 1 (1532)
[SoF;2] Special Function Out-
put 2 (1533)
[SoF;3] Special Function Out-
put 3 (1534)
[SoF;4] Special Function Out-
put 4 (1535)
[tMr] Timer (244)
[`uAr] Variable (245)
None 7192
[offset 50]
0x83 (131)
1 to 16
2
- - - - 31002 uint
RWES
[`Si;B]
[ Si.b]
Timer (1 to 16)
Source Instance B
Set the instance of the
function selected above.
1 to 250 1 7196
[offset 50]
0x83 (131)
1 to 16
4
- - - - 31004 uint
RWES
[`S2;B]
[ SZ.b]
Timer (1 to 16)
Source Zone B
Set the zone of the function
selected above.
0 to 16 0 7200
[offset 50]
0x83 (131)
1 to 16
6
- - - - 31006 uint
RWES
[sas;b]
[SAS.b]
Timer (1 to 16)
Source Active State B
Set what state will be read
as on.
[high] High (37)
[LoW] Low (53)
High 7212
[offset 50]
0x83 (131)
1 to 4
0xC (12)
- - - - 31012 uint
RWES
[``ti]
[ ti]
Timer (1 to 16)
Time
Set the time span that will
be measured.
0 to 9,999.000 1.0 7214
[offset 50]
0x83 (131)
1 to 16
0xD (13)
224 31013 float
RWES
[`LEu]
[ LEv]
Timer (1 to 16)
Active Level
Set which output state will
indicate on.
[high] High (37)
[LoW] Low (53)
High 7216
[offset 50]
0x83 (131)
1 to 16
0xE (14)
- - - - 31014 uint
RWES
Note: Some values will be rounded off to fit in the four-character display.
Full values can be read with other interfaces.
If there is only one instance of a menu, no submenus will appear.
R: Read
W: Write
E: EEPROM
S: User
Set
Komentarze do niniejszej Instrukcji